Ripping up the (January) Blues

January. Month of the blues. That typically means blue fingers and toes. The misery of missing out on our evening sunset rides, the (blue) icy weekend club rides and avoiding the usual club run route thanks to blue stuff (or brown!) running at pace down the street having spilled it’s banks.

But for me, this January has been 2 different kinds of blue. Cyan and the Blue Run.

Clean bike? Clearly not yet started!

Clean bike? Clearly not yet started!

This time last year I started my hunt for a CX bike. I didn’t want to spend a huge amount and would be more than happy with a 2nd hand bike. That’s fine for most, but do a search for new CX bikes at my height (that’s 158cm for those of you that haven’t met me) and it’s a struggle, let alone approaching the second hand market. 12 months on and with the help of a friend in Holland, I finally became owner to another Bianchi frame in some very traditional Bianchi colours.

The Bike Build
With the BB fitted by the local bike store, I was determined to build the rest of the bike myself. OK, I say myself, I had some help! But even then, it was easier said than done. Firstly, it’s the little things you don’t think about, resulting in a couple of trips to and forth from the bike shop to pick up ferrules and cable guides that I hadn’t considered when making my list of components (does such a list exist?).

Fitting the rear derailleur I realise I’m missing a bolt. Being Campag it’s not so easy to replace and so onto eBay to buy an old mech for parts. In the meantime, we fit the brakes, some snazzy Planet-X Frog Bolloxs which should be simple but, what I later learn is called the yoke, snaps as we tighten it. Bugger! Bike build on hold again until I can find a replacement.

Finally with the rear mech fixed and fitted, we attempt the gear routing. Campag specific wire goes through hole A and and comes out hole B….. at least, that’s what the instructions told us to do… did it work? NO! So, a couple of emails to a Campag mechanic friend and some handy tips and tricks shared, the gears are finally working. Rear mech fitted, bike is now working as a fixed gear at least. Just the front mech to complete…. and this is where we hit the wall. The wire is holding perfectly in the shifter, but can we get it to hold at the front mech? Can we heck. Getting a little impatient and really wanting to hit the trails, we give in and I drop the bike into the shop for them to complete the job and check over our work.

So finally, after 4 – 5 weeks of bike building (and a little over budget), I excitedly picked it up yesterday.  Bike number 6 took pride of place in the living room for the evening. But there was something significantly wrong – it was looking too new!

Hitting the Trails
Waking up to icy roads this morning, I jacked in the club ride, packed the car and headed over to Swinley Forrest in Bracknell.  My little brother spent much of his teens riding his fixed jump bike here, but this was the first time I’d ventured over there. I quickly realise what I’ve been missing out on.

The car park is packed with mtb-ers and walkers. I quickly ask a passer-by what state the trails are in – Good luck on a CX! They’re pretty unridable this morning’. Great. Well, I’m here now, so may as well give it a go. After all, my main intention is to get MUDDY!

Stopping to catch my breath at top of the sngle track on Blue Run

Stopping to catch my breath at top of the sngle track on Blue Run

I set off following the signs for ‘Mountain Bike Trails’ and soon come across a comprehensive hub detailing the different routes by distance and technical ability. Not much different to ski runs, the trails are set up from Green Run – 1.2km long with gentle dips on a wide track suitable for complete beginners and families, through to Red Run – 13km of extremely technical terrain of single twisty tracks with boardwalk climbs and lumpy descents, all of which are clearly marked in sections throughout.

New to the trails, CX and my bike, I start off on the Green Run and do a couple of warm up laps. It was great to see a 5 year old girl testing out her new bike skills with some expert advice from her MTB Dad, Helen Wyman’s going to have some competition!

Satisfied with the response of my brakes and gears, and slowly getting used to a different kind of cleats, I move onto the Blue Run.

Moderately graded, the complete route is 10.1km long and designed for novice to intermediate Mountain Bikers. It starts out on a pretty wide (although muddy) path, quickly descending into a single track through the pine forest. With some sections of the trail called “Full Nine Yards“, “Devils Highway” and “Stickler“, it’s not hard to imagine why this isn’t suited to the beginner. I also can’t imagine too many new to CX would be so comfortable either, but sticking to my rule of ‘always commit’ and wearing my ‘Fearless’ nick-name on my sleeve, I managed to weave, descend, jump and climb my way down the run.

I very quickly felt comfortable on my bike – trying to keep my pedal stroke smooth, I powered through thick mud; surprisingly managed to climb up over some steep sections stepped with tree roots, put my BMX lessons to use in the pump sections and only once came off track, luckily getting on the brakes to come to a clean stop before heading awol into some trees.

Other riders were extremely friendly, stopping for a quick chat and happy to sit behind until safe to pass or pull up to let you through. I managed 3/4 of the route before I started to get numb hands, even though I was wearing MTB gloves. Each section intersected by the fire-roads, it’s easy to drop off once you’ve had enough (although funnily enough, I found these harder to ride than the trails as they were so deep in mud!).

It may have been 2 degrees when I set out, but I was anything but cold. The blue run was a success and as I came to the end, part of me wanted to go at it all day. But car parking ticket due to expire, I followed the signs back to The Look Out.

I wasn’t expecting to enjoy it as much as I did and at least expected a fall here or there (who knows what the MTBer was on about when he said it was un-ridable!). With a CX sportive coming up in 2 weeks time, I can’t wait to get back on the bike.

Bianchi & Giro

What I rode:
Bianchi D2 Cross with Campag Veloce 10sp
FSA Omega Compact Road Bar with Deda Elementi Zero1 Stem
Ambrosio WS 23 Wheels with Schwalbe CX Comp Cyclocross Tyres and Planet X Frogs Bollox Cantilever Brakeset
Shimano Deore XT M780 SPD XC Race Pedals

What I wore:
Not much different to my every day cycling kit – bibs, leg warmers, Helly Hanson long sleeve base layer, Bianchi Winter Jersey, Skoda wind & rain proof jacket and a neck buff.

Giro Reva Womens MTB Shoe – these were surprisingly comfy for a first ride!
Specialized BG Gel WireTap Glove (A little big for me, these started to rub where padding meets handlebar)

 

 

 

Hayley Davies

Hayley Davies

Writer

Riding since Feb 2011 Hayley is a 30 year old female who loves adventures. If she’s not on one of her many bikes or in the water on a bodyboard/surfboard, then Hayley is probably out looking for something new to keep the adrenaline pumping!
Website: www.hjdonline.co.uk

Hardtail MTB or CX?

Hardtail MTB or CX?Can you ever have too many bikes?

Well I suppose it depends who you ask the question of! In our household I would naturally answer No of course you can never have too many, however my wife might just answer rather differently posing a question of her own. How many bikes can you ride at any one time!

Seriously though you do need a bike for each discipline you ride, don’t you. Who in their right mind would use a track bike to ride a BMX course and like wise who would ride downhill on a CX (cyclocross) bike! OK so I have chosen some extremes but I still recon that you need more then one bike.

Unlike some I am not totally mad with the number bikes I have and I have a sensible mix, a road bike (actually two if I am honest), an full suspension XC MTB, a track bike and a BMX.

Over the years the type of riding I have been doing has changed a little and the Full Suspension XC seems a bit of an over kill for riding things like Preston’s Guild Wheel and some of the disused railway lines locally, however a full carbon road bike does not quite fit the bill either! Leaving me with a bit of a conundrum, what to get to fill the gap? A hard tail MTB to replace the Full Sus or a CX bike?

Hmm tricky coz I really do not want to get rid of the Full Sus because it is really useful for those days out in the hills and trail centres. I know I could do these on a hardtail but then just maybe this would be over kill for the local trails.

Yes you guessed it I plumped for a CX bike, as I said you can never have too many bikes!! But I set myself a challenge I had to do this on a budget no more then £300 could be spent. I had a donor bike for most of the drive train and bars etc, so all I needed would be a frame, brakes, wheels and tyres.

My natural port of call for these parts was going to be ebay or discount online stores. First things first find out what is needed for a CX bike and which parts are the most robust for a bit of a hack bike and how much parts typically are. This is key to avoid over spending on eBay. It always amazes me that many buyers on ebay get carried away. The worst I have seen is a set of wheels go for £30 more then the buy now option for the same set from the same seller who had one set on open bid and another set available as buy now!

The donor bike was a Specialized Allez Sport with Shimano Tiagra triple chainset. I pondered long and hard over the triple chainset as my gut instinct was to go for a double CX specific or a double compact until I read this article http://bikehugger.com/post/view/the-rise-of-the-compact-crank which clearly defined the pit falls of a compact and the benefits of the triple. The decision to stick with the triple also meant I had less to buy with my budget, meaning more to spend on the frame.

Kinesis Crosslight Evo4 Cyclocross Frame 2010

Kinesis Crosslight Evo4 Cyclocross Frame 2010spend on the frame.spend on the frame.

 

Step 1 Frameset.

 

Having trawled eBay and the internet it seemed that the choices boiled down to a selection from:

 

  1. Graham Weigh frame and forks £199.99
  2. Forme Hiver (Paul Milnes) £274.99
  3. Paul Mines CT Wing £295
  4. Dolan Multicross  £249.99

 

From these the best value for money seemed to be the Dolan as it included a seat post, headset and front cable hanger. However this did not leave me with much in the budget for wheels. So back to the drawing board and review the second hand options via eBay. Patience and timing had to be the watch word now. As I write there are very few frames on open bid. I missed out on a couple by a few pounds but I had set my target and was sticking to it.

Finally I hit the jackpot with a rather good Kenesis Crosslight EVO4 and BikeRadar’s review seemed to rate the frame

(http://www.bikeradar.com/gear/category/bikes/cyclo-cross/product/review-kinesis-crosslight-evo-4-11-45404)

Brakesso in for a penny in for a few quid!

 

Step 2 Brakes

 

The frameset was set up for cantilevers only but which set to get? Shimano CX50’s, Avid ShortyTektro V brakes, Empella Froglegs or Tektro CR 520?

Cash had to be king here and simplicity had to rule so a big thanks to Paul Milnes eBay store Tektro Colorado’s at £21.99 a full set it was

 

Step 3 Wheelset.

 

I struck gold here as a friend who had switched from a CX bike to a 29er still had a set of Shimano wheels that came off his Cannondale CX bike so £40 landed me 5 tyres and tubes and a set of Shimano WH-RS10’s. Not the most amazing Cablesetwheelset in the world but functional.

 

Step 4 cable set.

 

Having used a mix of manufacturers in the past decided to try a new manufacturer for me and bought a set of low friction PTFE-coated stainless steel Goodridge cables from Chainreaction (user reviews 4.1/5).

 

CX ForksThe Build.

 

The first thing to do was to strip down the donor bike a Specialized Allez Sport running a triple Shimano Tigra groupset. I would be using everything from this bike except the caliper brakes and saddle, or at least that was the plan.

As soon as the frame arrived from its original Coleford Gloucestershie home it was time for close inspection. The frame was pretty much as described on eBay except for a very small dent on the downtube and a small gouge hidden under a sticker on the headtube. If I am being really picky the packing of the frameset could have been better and I was rather disappointed that the seller had not used fork and rear end frame spacers to avoid crushing during shipping as I had requested. The good news was the frame was in full alignment and ready to build.

A quick clean down and removal of old cable protectors and it was time to apply helicopter tape to areas which might suffer from scuffing, cable wear or chain slap.

This done it was in with the bottom bracket, crankset and front mech, quickly followed by rear mech, handlebar stem, seat post, handlebars and finally cantilever brakes and wheels. Time to check the fit. First hop on and it was immediately obvious that the handlebar stem was going to be a tad too short. So out with the tape measure and size up the fit vs my road bike. It was very obvious that the 100mm stem going to be too short. 110 mm might just work but even this might leave me a little hunched up, so it would need to be 115 or 120mm. I plumped for the longer of the two a quick trawl on the internet and a 120mm Deda Zero 1 was acquired and fitted. Perfect sizing and hey presto one bike ready for setting up with cables.

First Impressions CX

The Goodridge cables where new to me and I was itching to find out how good they really where. Unlike normal brake cables which have flat spiral wound metal the Goodridge set are the same set up as a gear cable outer, with steel strands in the sheath orientated in the same direction as the cable (along the length of the outer).  For gear cables this reduces compression of the outer and improves reliability of indexing.

Kinesis Pure CX Cyclocross Fork

Kinesis Pure CX Cyclocross Fork

I will be interested to see the effect on braking. I suspect that it will improve modulation and feel reducing any sponginess caused by the outer compressing during braking. The brake cables certainly proved to be very stiff and somewhat tricky to cut.

With careful measuring and cutting (measure twice cut once) all was well with both gear cables and brake cables. A really nice touch with the Goodridge set is the long leadin tails on the cable ferrules allowing for improved

water and grit protection. With careful fitting of the blue plastic outer it is possible to run the cables fully water and grit proof.

All finished time to ride.

 

First Impressions.
Bars CXWOW this is a quick bike. From the first turn of the pedals it is clear that this is a race bike with a real eagerness to move forwards quickly. To quote What Mountain Bike’s review

“The Kinesis Crosslight Evo is a highly evolved racer that proves even hardcore cyclo-crossers can be a fun and versatile trail/tarmac crossover option on non-race days.” 

Very true and great fun was had on the first few rides proving that it was a very good choice to go CX and not Hardtail. However as time went on a couple of limitations started to show through and once again these confirmed the finding of Guy Kesteven

‘A major – but surprisingly common – technical terrain limitation soon becomes clear though. While the Tektro cantilever brakes on the Kinesis are usefully powerful – at least in the dry – the brake judder caused by fork flex on rough terrain makes the front wheel skip alarmingly.’

fork crown cable stopfront wheel skip was the least of the problems the fact was that the amount of front brake judder, especially during descents, made the front brake totally redundant. Solution simples, fit a fork crown cable stop to replace the headset one. Cost £8.99 from Paul Milnes. Fitted cable recut and off we go again. Amazing the front brake is a different beast no judder at all even under the most powerful braking, bringing a high level of confidence to tackle technical descents with ease. Does make you think as to why Kenesis do not fit this simple device to the OEM bike in the first place. £8.99 is not a major cost to transform the ride.

 

Conclusion

 

MTB or CX well this being my first CX ride ever I am totally sold. This has to be the perfect tool for riding the local disused railway lines and simpler off road tracks, where to be honest even a hard tail MTB would be overkill.

What is even better is that I have managed to build a CX  worth over £1000 for £300, result! Will I get rid of my Full Sus MTB? No it is horses for courses and to attack trails like Gisburn, Winlatter, Grizedale etc this will still be the machine to use but for a qucik blast along many of the SUSTRANS off road routes the CX EVO 4 will be perfect.

If you have never tried a CX bike and want to venture offroad but do not want to wreck your best road bike then find a frame on eBay and switch all your winter hardware onto a CX frame.

 

Subscribe for 10% Discount!

Join our mailing list to receive the latest cycling news and updates from our team. Receive 10% off your first order placed in our online shop!

You have Successfully Subscribed!